Bolt, Washer & Nut Kit (Rear Shock Mounting) RH for Bullet 350 UCE / Electra 350 UCE / Classic 350 / Classic 500 EFI / Bullet 500 UCE – 888098 (Right Side)

Royal Enfield 888098 is the Rear Shock Absorber mounting fastener kit (Right-Hand side)—a genuine hardware set used to secure the RH rear shock on several Royal Enfield UCE-era motorcycles. If your rear shock bolt/nut is rounded, missing, rusted, mismatched, or you’re rebuilding the rear suspension after an accident/paint job, this kit prevents unsafe play and helps restore correct fitment.

Because suspension mounting points take continuous load and vibration, using the correct OEM-spec bolt/washer/nut stack matters for durability and alignment—especially if your bike has seen local workshop “jugaad” fasteners.

Also searched as: rear shock bolt kit RH, shocker nut bolt set, rear suspension bolt washer nut kit, rear shock mounting bolt kit 888098, PS888098.

Before you buy: confirm your bike is UCE/older platform (not J-Series) and you need RIGHT side hardware (LH kit is different).

Key Features 

• Genuine-style Rear Shock hardware kit for RH (Right) side (kit quantity = 1 set)

• Designed for UCE-era rear suspension mounting stack (bolt + washers + lock washer + nut as per catalogue listing)

• Ideal for replacing rusted / stripped / incorrect rear shock fasteners

• Helps prevent loosening, play, clunking and misalignment at rear suspension mount

• Correct, repeatable hardware set—better than mixing local fasteners of unknown grade

• Useful during rear shock replacement, chassis restoration, repaint, or accident repair

• Right side only; LH side uses a different kit/part number (see Variants)

Compatibility Table 

Explicit exclusions (return-prevention): Not for J-Series bikes (Classic 350 Reborn, Bullet 350 J, Hunter 350, Meteor 350), not for 650 Twins, Himalayan 411/450, etc. (no supporting EPC/dealer confirmation for those).

Variants

• RH kit (this product): 888098 – Rear shocks bolt/washer/nut kit (Right side)

• LH kit (related): 888099 – Rear shocks bolt/washer/nut kit (Left side)

FAQs 

Q1 (Fitment): How do I confirm this 888098 kit is for my bike?
Check your bike is UCE-era (Classic 350 UCE / Classic 500 EFI / Bullet 350 UCE / Electra 350 UCE / Bullet 500 UCE). Then confirm you need RIGHT side (RH) rear shock mounting fasteners. EPC pages list 888098 as the RH kit in the rear shock absorber group.

Q2 (Fitment): Will it fit Classic 350 Reborn / Hunter 350 / Meteor 350?
No confirmation exists for J-Series models for part 888098. J-Series rear suspension hardware differs; ordering this for Reborn/Hunter/Meteor is a common mismatch return.

Q3 (Comparison): OEM/genuine-style kit vs local fasteners—why pay more?
Shock mounts carry load + vibration. Correct-grade bolt, washer stack and locking method reduces loosening and wear at the mount. Local mixed fasteners often cause play, clunking, or thread damage over time.

Q4 (Installation): Any precautions while fitting this rear shock bolt kit?
Support the bike safely (center stand/jack), unload the rear suspension before removing the shock bolt, fit the washer order correctly, and torque to service manual spec for your model. Re-check torque after a short ride.

Q5 (Symptoms): What problems does this kit solve?
Loose/clunking rear end, missing shock nut/washer, rounded bolt head, rusted hardware after monsoon, or incorrect workshop bolts used during shock replacement.

Q6 (Returns-prevention): What should I share to verify before dispatch?
Send a photo of your RH rear shock top/bottom mount area and mention exact model + year/engine (UCE vs J-Series). If you’re unsure about RH vs LH, send photos of both sides.