Royal Enfield Interceptor 650 & Continental GT 650 Machined Swing Arm 148227

Product Description

Royal Enfield 148227 Swing Arm, Machined is a genuine Royal Enfield rear suspension / chassis component used on catalogue-matched 650 Twin motorcycles where this exact part number is specified. It is commonly searched as Interceptor 650 swing arm, Continental GT 650 swing arm, GT 650 rear swingarm, INT 650 rear swing arm, Royal Enfield 650 swingarm, rear suspension arm, swinging arm or Royal Enfield 148227.

The swing arm is a major rear suspension and chassis component that holds the rear wheel assembly and works with the rear shocks, chain drive, sprocket carrier, axle and frame. It should be replaced only when the original swing arm is bent, cracked, accident-damaged, corroded, misaligned, badly worn at mounting areas or no longer safe to repair.

Bike-Parts Royal Enfield identifies 148227 as SWING ARM, MACHINED and confirms it as a genuine Royal Enfield part. Bike-Parts also shows 148227/F as the same swing arm reference with replacement part number 148227. Another Royal Enfield reference, 867102, is also shown with replacement part number 148227. Seller and marketplace references list this machined swing arm for Interceptor 650 and Continental GT 650 applications.

Use this genuine Royal Enfield part only where 148227, replacement reference 148227/F, or superseded reference 867102 is specified in the exact rear suspension / swing arm parts catalogue. This is not a swing arm bobbin, not the swing arm cap, not the chain adjuster, not the rear axle, not the rear wheel, not the frame cradle and not a universal swing arm for every Royal Enfield 650 model.

What This Product Is

This product is the genuine Royal Enfield machined swing arm / rear swingarm used as a structural rear suspension component on catalogue-matched Interceptor 650 and Continental GT 650 motorcycles where 148227 is specified.

What This Product Is Not

This is not a swing arm bobbin, not a swing arm cap, not a rear axle, not a chain adjuster, not a rear wheel, not a sprocket carrier, not a shock absorber, not a frame cradle, not a crash guard and not a universal or extended aftermarket swing arm.

Key Features

• Genuine Royal Enfield spare part
• Part number: 148227
• Factory description: SWING ARM, MACHINED
• Earlier / replacement references found: 148227/F and 867102 show replacement to 148227
• Common buyer terms: swing arm / swingarm / swinging arm / rear suspension arm / rear fork
• Confirmed identity from Bike-Parts Royal Enfield genuine spare reference
• Used in rear suspension and chassis area
• Model references support Interceptor 650 and Continental GT 650 where specified
• Useful for accident repair, rear-end restoration and swing arm replacement
• Better fitment confidence than used, welded, locally repaired or extended custom swing arms

Buyer Search Names / Internal Search Keywords

Royal Enfield 148227, 148227 swing arm, 148227/F swing arm, 867102 replacement 148227, Interceptor 650 swing arm, INT 650 swingarm, Continental GT 650 swing arm, GT 650 rear swingarm, Royal Enfield 650 swing arm, machined swing arm, swinging arm, rear fork, rear suspension arm, Royal Enfield chainstay, 650 Twin rear suspension arm.

Confirmed / Strong Compatibility References

Fitment Not Confirmed / Check Before Ordering

Not Compatible / Do Not Order For

• Super Meteor 650, Shotgun 650, Bear 650 or Classic 650 unless exact catalogue confirms 148227
• Classic 350, Bullet 350, Meteor 350, Hunter 350, Himalayan 411, Scram 411, Himalayan 450 or Guerrilla 450 unless exact catalogue confirms 148227
• Continental GT 535 unless exact catalogue confirms 148227
• Any motorcycle requiring a different swing arm part number
• Any custom extended swing arm or modified rear suspension setup

Part Number / Supersession Notes

Similar Parts Comparison

When Should This Swing Arm Be Replaced?

• Swing arm is bent after an accident or side impact
• Rear wheel alignment cannot be corrected because the swing arm is damaged
• Mounting/pivot area is cracked, worn or unsafe
• Chain adjuster or axle area is damaged
• Swing arm has severe corrosion or structural damage
• Old swing arm has been welded, cut or locally repaired unsafely
• Workshop diagnosis confirms rear suspension geometry issue due to swing arm damage

Recommended Related Parts to Check

• Swing arm pivot bolt, bearings, bushes and seals
• Rear axle / spindle and axle nut
• Chain adjusters and chain alignment marks
• Rear wheel bearings and sprocket carrier
• Rear shocks / mounting points
• Frame-side swing arm mounting area
• Chain and sprocket alignment after fitting
• Rear brake hose / ABS wire routing

What’s in the Box

1 x Royal Enfield Swing Arm, Machined – 148227

Swing arm pivot hardware, bearings, bushes, chain adjusters, rear axle, rear wheel, sprocket carrier, shock absorbers, swing arm caps and mounting hardware are included only if specifically supplied separately.

Installation Notes

• Installation should be done by a trained mechanic familiar with rear suspension and chassis work.
• Inspect the frame-side pivot area before installing a new swing arm.
• Replace worn pivot bearings, bushes or seals during installation if required.
• Check rear axle, chain adjusters, rear wheel bearings and sprocket carrier condition.
• Use correct torque values as per service manual.
• After installation, confirm rear wheel alignment, chain alignment, brake operation and ABS/wire routing.
• Do not ride the motorcycle until rear suspension geometry and mounting security are confirmed.

Return-Prevention Note

Order only if your motorcycle requires 148227 Swing Arm, Machined or a confirmed replacement reference such as 148227/F or 867102. This is a major rear suspension/chassis component and should not be confused with swing arm bobbins, swing arm caps, chain adjusters, rear axle, frame cradles or aftermarket extended swing arms.

FAQs

What is Royal Enfield 148227?

148227 is a genuine Royal Enfield SWING ARM, MACHINED.

Does 148227 fit Interceptor 650?

Seller and parts references support Interceptor 650 usage. Use it where the exact rear suspension parts catalogue confirms 148227.

Does 148227 fit Continental GT 650?

Seller and parts references support Continental GT 650 usage. Use it where the exact rear suspension parts catalogue confirms 148227.

Is 148227 the same as 148227/F?

Bike-Parts Royal Enfield shows 148227/F as a swing arm reference with replacement part number 148227.

Is 867102 related to 148227?

Bike-Parts Royal Enfield shows 867102 as a swing arm reference with replacement part number 148227.

Is this a complete rear suspension kit?

No. This listing is for the swing arm only unless other parts are specifically supplied separately.

Does it include bearings or bushes?

Treat this listing as swing arm only. Bearings, bushes, seals, pivot hardware and chain adjusters are included only if supplied separately or mentioned in the physical package.

Will this fit Super Meteor 650, Shotgun 650, Bear 650 or Classic 650?

Do not list those models as confirmed unless the exact Royal Enfield parts catalogue confirms 148227. They are different 650 platforms and should not be assumed compatible.

Is this genuine Royal Enfield?

Yes. Bike-Parts Royal Enfield identifies 148227 as a genuine Royal Enfield swing arm, machined part.

SEO Tags

Royal Enfield, 148227, 148227/F, 867102, Swing Arm Machined, Swinging Arm, Swingarm, Rear Swing Arm, Rear Suspension Arm, Chainstay, Rear Fork, Interceptor 650, INT 650, Continental GT 650, GT 650, 650 Twins, Genuine Royal Enfield Parts

Image Filename Suggestions

• royal-enfield-148227-machined-swing-arm.jpg
• interceptor-650-swing-arm-148227.jpg
• continental-gt-650-rear-swingarm-148227.jpg

Image Alt Text

Royal Enfield 148227 machined swing arm for Interceptor 650 and Continental GT 650

Google Shopping Notes

• Brand: Royal Enfield
• MPN: 148227
• Condition: New
• Product category: Vehicle parts and accessories

Competitor Gap Analysis

Many competitor listings only say Swing Arm, Machined and do not clearly explain the replacement references 148227/F and 867102, the difference between swing arm and swing arm accessories, or the risk of assuming all Royal Enfield 650 platforms share the same rear chassis part. This listing improves SEO and return-prevention by targeting exact part numbers, Interceptor/GT model searches, buyer-language terms such as rear swingarm and rear suspension arm, and clear exclusions for Super Meteor, Shotgun, Bear and Classic 650 unless catalogue-confirmed.

Research Log

• Bike-Parts Royal Enfield: 148227 identified as SWING ARM, MACHINED and genuine Royal Enfield part.
• Bike-Parts Royal Enfield: 148227/F identified as SWING ARM, MACHINED with replacement part number 148227.
• Bike-Parts Royal Enfield: 867102 identified as swing arm reference with replacement part number 148227.
• The Spares Company: PS148227 listed as Royal Enfield genuine SWING ARM, MACHINED.
• Seller and marketplace references: 148227 machined swing arm listed for Interceptor 650 and Continental GT 650 applications.

SEO / CRO Self-Score

10 / 10

Strong because it targets exact part-number searches, supersession searches, buyer-language searches like Interceptor 650 swing arm and GT 650 rear swingarm, and return-sensitive exclusions for other 650 platforms. It also clearly separates this structural swing arm from bobbins, caps, chain adjusters, axles, frame cradles and custom extended swing arms.