Royal Enfield RAQ01301/B – Rubber Beading, Shroud for Bullet 350 BS6 (Tail Lamp / Number Plate Shroud Seal – Genuine OEM)

The Royal Enfield RAQ01301/B Rubber Beading, Shroud is the genuine factory rubber seal that sits around the tail-lamp / number-plate shroud on the new Bullet 350 BS6 (J-Series). It is designed to create a tight, rattle-free seal between the shroud and the rear mudguard, keeping out dust, mud, and water while protecting your paint from vibration marks.

Over time, this beading can harden, crack, or get damaged during rear-end impacts or tail-lamp repairs. Replacing it with an original RAQ01301/B beading restores the factory finish and prevents annoying squeaks and panel gaps. As an OEM part from the official Royal Enfield spares catalog, it matches the exact profile, length, and softness required for the Bullet 350 BS6 shroud assembly, ensuring easy, plug-and-play fitment with no cutting or modification.

This beading is ideal for accident repairs, restoration jobs, or riders converting an aftermarket setup back to stock. If you’re already using the genuine RAQ01305/A shroud assembly on your Bullet 350, RAQ01301/B is the correct companion seal to complete the installation.

Choose original Royal Enfield rubber components for long-term durability, better weather sealing, and a neat OEM look on your Bullet’s rear end.

Key Features

• Genuine Royal Enfield OEM rubber beading – Part No. RAQ01301/B

• Specifically profiled for the tail lamp / number plate shroud on Bullet 350 BS6

• Maintains a dust- and water-resistant seal between shroud and rear mudguard

• Helps eliminate rattles, vibrations, and paint wear around the shroud area

• Soft yet durable rubber compound for long service life in Indian weather

• Direct replacement – no trimming or modification required when used with OEM shroud

• Works perfectly with RAQ01305/A Shroud Assembly (Black) for Bullet 350 BS6

• 100% authentic spare sourced from Royal Enfield supply chain, not local aftermarket

• Compact, lightweight part – easy to ship and carry as a spare in your workshop

Compatibility Table 

*Confirmed from the official Royal Enfield parts microfiche where RAQ01301/B – Rubber Beading, Shroud is listed under Bullet 350 > B5G – VGLH09MK. Other Bullet 350 BS6 colour/trim variants are expected to use the same beading, but if your bike is not a 2023-onwards J-Series Bullet 350, please confirm by VIN or consult us before ordering.

Variants

• Single Variant: RAQ01301/B – Rubber Beading, Shroud
  (Single piece beading for one shroud; no LH/RH or colour options)

FAQs

Q1. Will RAQ01301/B fit my older Bullet 350 UCE or Classic / Electra models?
No. This beading is listed specifically for the 2023-onwards Bullet 350 J-Series (BS6). Older UCE Bullet, Classic, or Electra models use different shroud / number plate beading profiles and part numbers.

Q2. Do I need this beading if I replace the tail lamp shroud (RAQ01305/A)?
Yes, for best results. Whenever you change the shroud assembly, you should also fit a fresh rubber beading so the panel seals properly and does not rattle. RAQ01301/B is the matching beading for the Bullet 350 BS6 shroud.

Q3. Can I reuse my old beading if it looks fine?
You can, but it’s not recommended. Aged rubber compresses and hardens, which can lead to poor sealing, water ingress, and squeaks. Replacing it while the shroud is already off is inexpensive and ensures a factory-fresh fit.

Q4. Is any adhesive required to install this beading?
In most cases, no extra adhesive is needed – the OEM profile grips the shroud and mudguard edge snugly. If your shroud has minor surface wear, a thin strip of OEM-grade rubber adhesive or double-sided tape can be used at a few points for added security.

Q5. How do I confirm fitment with my bike?
Check that your RC / owner’s manual lists Bullet 350 (349cc J-Series, BS6) and your VIN prefix starts with the new Bullet BS6 platform code (e.g. B5G). When in doubt, share your VIN or a photo of the rear shroud area with us before purchase.