SAP Swiss Electric
SAP Swiss SAP-0168C Speedometer Socket Wiring Assembly – Royal Enfield Classic 500 ES (2011–2016) | 9-Pin, 4 Holders
SAP Swiss SAP-0168C Speedometer Socket Wiring Assembly – Royal Enfield Classic 500 ES (2011–2016) | 9-Pin, 4 Holders
Couldn't load pickup availability
Please confirm the part number and compatibility before ordering.
Complete Your Order
Motul Chain Maintenance Kit – C1 Chain Cleaner + C2 Chain Lube Road (150ml Each) – Motorcycle O-Ring/X-Ring/Z-Ring Compatible
33081208 - Metal Polishing - 15Gms Royal Enfield Metal Polish Chrome Polish For Bullet
Adds: 15 GMS
SAP Swiss SAP-0168C Speedometer Socket Assembly – Royal Enfield Classic 500 ES 2011–2016
Repairing a loose, burnt, corroded or damaged Royal Enfield Classic 500 speedometer socket, instrument-cluster wiring connector or meter lamp-holder lead? Swiss SAP-0168C is a replacement speedometer socket / meter wiring lead assembly specified for the Royal Enfield Classic 500 ES (2011–2016 models) that use the matching 9-pin speedometer connector and four-holder arrangement. It is an aftermarket electrical spare supplied by SAP Swiss Electric, not a complete speedometer or an original Royal Enfield-branded meter.
FITMENT FIRST — PLEASE READ: This part is specifically listed for Classic 500 ES, model years 2011–2016, with the matching 9-pin connector and four holder layout. It is NOT advertised as a universal fit for Classic 350, Thunderbird 350/500, Electra, Bullet Standard, Machismo, Himalayan, Classic 350 Reborn, New Bullet 350 or other J-series motorcycles. Even within the stated year range, compare your existing plug, wiring positions and holder arrangement before placing the order.
Product at a Glance
| Product | Speedometer socket / instrument-meter wiring lead assembly |
|---|---|
| Brand / manufacturer | SAP Swiss Electric Pvt. Ltd. (aftermarket Swiss-branded replacement) |
| Part number | SAP-0168C (also searched as SAP0168C or SAP 0168C) |
| Model listed by manufacturer | Royal Enfield Classic 500 ES – 2011 through 2016 |
| Connector specification | 9-pin speedometer socket |
| Holder configuration | 4 holders for the specified meter arrangement |
| Sale quantity | 1 complete socket lead assembly / set (not four independent sets) |
| Vehicle installation area | Behind/under the speedometer or instrument cluster, at the meter wiring and lamp-holder connection points |
| Printed pack MRP | ₹102, inclusive of applicable taxes; printed April 2023 – historical pack figure, not a current selling-price guarantee |
| Packing date on pack | April 2023 |
| Included | One SAP-0168C meter socket/wiring lead assembly as packed |
| Not included | Complete speedometer/instrument cluster, speedometer cable or sensor, main motorcycle wiring harness; bulb inclusion is not confirmed |
What Does This Socket Assembly Do?
The speedometer socket is part of the electrical connection serving the motorcycle meter/instrument area. Its connector and lamp-holder leads allow the original matching speedometer-side wiring connections to be made. This part may be used during repairs involving a damaged speedometer socket, deteriorated holder leads, loose instrument wiring connectors or faulty electrical contacts. The exact cause of a non-working meter or lamp must be diagnosed before purchasing: a broken speedometer cable, faulty speed sensor, dead bulb, blown fuse or instrument failure will not necessarily be fixed by changing this wiring lead.
The name “4 Holder With 9 Pin Socket” describes a specific wiring/holder configuration. Four holders does not mean four separate speedometer wiring sets. The package is sold as one assembly. Wire colours can vary by production batch, so do not use photographs as a pin-assignment or polarity diagram.
Verified Vehicle Fitment
| Motorcycle | Model years | Fitment qualification |
|---|---|---|
| Royal Enfield Classic 500 ES | 2011–2016 | Manufacturer-listed for the 4-holder + 9-pin speedometer socket; physically compare your existing connection |
Important: “Classic 500 ES” is the manufacturer’s application description. The model name, engine family or year alone is not sufficient to establish that the bike has the correct meter connector, especially on previously repaired or modified motorcycles. Check the old lead against the 9-pin connector body, number and shape of bulb holders, keying/latch and routing.
Models Not Covered by This Fitment Claim
- Royal Enfield Classic 350 (including older UCE Classic 350) – not specifically included in SAP-0168C manufacturer listing
- Classic 350 Reborn, Meteor 350, Hunter 350 and new Bullet 350 J-series – different-generation meter/wiring systems; not listed for this item
- Thunderbird 350/500 and Thunderbird X – no SAP-0168C compatibility verified
- Electra, Bullet Standard and Bullet Machismo – Swiss lists different socket references for certain older versions; do not assume the same lead
- Classic 500 model years outside 2011–2016 or vehicles with changed/aftermarket speedometers – inspect the original connector before ordering
Do Not Confuse SAP-0168C with Other Swiss Speedometer Socket Assemblies
| Swiss part | Manufacturer-listed application | Difference / buying guidance |
|---|---|---|
| SAP-0168C | Classic 500 ES (2011–2016) | This item: 4 holders with 9-pin speedometer socket |
| SAP-0168 | Bullet Machismo AC/DC | Different bike application; do not substitute by number similarity |
| SAP-0168A | Bullet Electra (2004 model) | Different model-specific speedometer wiring assembly |
| SAP-0168E | Bullet Machismo AC/DC | Catalogue describes T-10 bulb holder with 6-pin socket |
| SAP-0168F | Bullet Electra (2004 model) | Catalogue describes T-10 bulb holder with 6-pin + 2-pin sockets |
| SAP-0168G | Classic 500 ES (2011–2016) | Catalogue describes a T-10 bulb-holder configuration with 9-pin socket; verify holder type rather than assuming it is the same as SAP-0168C |
Why the comparison matters: A 9-pin description does not by itself prove that two assemblies have the same holder layout, connector key, cable length or wiring. For Classic 500 repairs, distinguish SAP-0168C from SAP-0168G by comparing the actual old assembly and holder design.
What You Receive
- 1 × SAP Swiss SAP-0168C speedometer socket / wiring lead assembly with the specified four-holder / nine-pin arrangement
- SAP-branded protective retail packing
- Not included: speedometer dial, instrument housing, meter cable, mechanical/electronic speed sensor, wiring loom for the whole bike or installation labour
- Bulbs or separate installation fasteners are not guaranteed unless specifically listed on the sales invoice or inspected package
When Would a Speedometer Wiring Lead Need Replacement?
- Broken, melted or badly corroded holder terminals or meter-side socket contacts
- A loose or damaged matching 9-pin speedometer connector
- Cracked/aged insulation near the meter harness or bulb-holder tails
- Intermittent meter illumination or warning-lamp connections after checking bulbs, battery voltage, fuses and other electrical causes
- Restoring a Classic 500 ES that has the correct original meter/connector arrangement
Diagnosis note: This is an electrical wiring repair part. It is not an assured remedy for a non-working speedometer needle, odometer, speed sensor, speedometer cable or instrument electronics. Identify the failed component before purchase.
Pre-Order Fitment Checklist
- Verify that the bike is a Royal Enfield Classic 500 ES, 2011–2016.
- Inspect the connector behind the original meter and confirm the 9-pin speedometer socket form factor.
- Check the number, size and fixing arrangement of the four lamp holders; not all speedometer holders are the same.
- Check the plug keying/lock, wire routing and holder lengths against the old lead. Do not infer pin assignments from wire colours.
- If your meter or wiring loom has been changed, send the old lead’s front/rear photos and model details for comparison before ordering.
Installation and Electrical Safety
- Disconnect the negative battery terminal before unplugging or replacing electrical connectors.
- Remove or access the meter/nacelle carefully; avoid pulling on the wires or tearing the terminal crimps.
- Check socket orientation, pin alignment, connector locking, holder retention and wiring routing before reconnecting the battery.
- Use the appropriate electrical contact inspection, waterproofing/insulation and repair methods; do not force a mismatched plug.
- Confirm meter illumination and indicator/warning lights function correctly after installation. Use a qualified motorcycle electrician if uncertain.
- Electrical product: installation or wiring alteration may make the item ineligible for return under the applicable product return policy; check compatibility before opening/installation.
Frequently Asked Questions
1. Is this a complete Royal Enfield Classic 500 speedometer?
No. SAP-0168C is the speedometer socket / wiring lead assembly. The speedometer unit and its housing are not included.
2. Which bike is SAP-0168C for?
The Swiss manufacturer lists Royal Enfield Classic 500 ES, 2011–2016 models, with the matching four-holder, nine-pin speedometer socket.
3. Will it fit my 2012 Classic 500?
It is within the listed model years, but confirm the original meter has the matching 9-pin connector and four-holder lead. A changed meter or harness may need another type.
4. Can I use it on a Classic 350 UCE?
Not as a verified fitment. The manufacturer listing for SAP-0168C specifies Classic 500 ES, not Classic 350. Compare the old assembly and obtain confirmation before ordering.
5. Will it fit a Classic 350 Reborn or other J-series Royal Enfield?
No J-series fitment is listed for SAP-0168C. Do not buy it for Classic Reborn, Meteor, Hunter or New Bullet 350 on this listing.
6. Will it fit a Thunderbird 350 or Thunderbird 500?
Not verified. The SAP-0168C manufacturer application specifically refers to the older Classic 500 ES 2011–2016, not Thunderbird.
7. Is SAP-0168C suitable for a 2017 or later Classic 500?
The manufacturer lists the 2011–2016 range. Do not assume later-year fitment without matching the existing meter-side connector and holder arrangement.
8. What does 9-pin socket mean?
It identifies the connector style used at the speedometer wiring lead. Pin count alone is not enough to prove interchangeability: connector housing, pin positions, keying and wiring must also match.
9. What does four-holder mean?
It refers to the four meter lamp-holder positions in this specified assembly. The box contains one complete wiring/holder assembly, not four separate assemblies.
10. Are all four bulbs included?
The photographs and manufacturer description verify the holder assembly but do not establish bulb inclusion. Bulbs should not be assumed included.
11. Are SAP-0168C and SAP-0168G the same?
Do not assume so. Both appear in Swiss Classic 500 ES applications, but the catalogue separately describes SAP-0168G as a T-10 bulb-holder version with a 9-pin socket. Compare the holder configuration.
12. Can SAP-0168A or SAP-0168E be used instead?
No equivalence is established. SAP-0168A is listed for older Electra while SAP-0168E is a 6-pin Machismo/T-10 holder assembly. Match the original part.
13. Will this fix my speedometer not working?
Only if the cause is the faulty meter-side socket/wiring that this assembly replaces. A cable, speed sensor, instrument or fuse fault requires its own diagnosis.
14. Does this replace the main wiring harness?
No. This is the smaller meter-side socket/wiring lead assembly, not a full main motorcycle wire harness.
15. Is it an original Royal Enfield OEM product?
No. This is a SAP Swiss Electric aftermarket replacement part designed for the specified Royal Enfield meter arrangement.
16. How many do I need to order?
One order contains one SAP-0168C socket lead assembly/set. This is normally selected as one assembly for the stated repair, subject to the actual fault.
17. Can I match it from wire colours alone?
No. Colour alone is not a reliable identification or wiring guide. Compare the 9-pin connector, the number and shape of holders, and the old harness layout.
18. Does the Under The Hood lanyard shown in some photos come with this?
No. Any UTH lanyard/keychain used for product-photograph identification is not included with the SAP-0168C electrical part.
19. What should I check before opening or installing?
Verify Classic 500 ES 2011–2016 model, 9-pin connector housing, four-holder layout, and wire routing. Electrical goods may not qualify for return after opening/installation under applicable policies.
Final Buying Note
Buy SAP Swiss SAP-0168C only when your Royal Enfield Classic 500 ES (2011–2016) uses the matching 9-pin speedometer connector and four-holder lead. It is a single aftermarket meter socket wiring assembly, not a complete speedometer. For any other motorcycle, newer model year or modified meter, confirm the original assembly before ordering.
Share
Verify Fitment on Official Brand Portals
Verify Fitment on Official Brand Portals
For selected genuine spare parts, you can cross-check the part number on the official brand portals before ordering.
Royal Enfield Official Spares Portal
Hero MotoCorp Official eCatalogue

Become a Dealer Partner
We supply 100% genuine OEM parts to workshops and dealers across India. Our team will reach out within 24 hours.