Deutsche / Swiss Auto
Deutsche DEUS-1035Y Black Amber Indicator for Royal Enfield Classic 350 BS6 UCE / Classic 500 UCE – Front or Rear (1 Piece)
Deutsche DEUS-1035Y Black Amber Indicator for Royal Enfield Classic 350 BS6 UCE / Classic 500 UCE – Front or Rear (1 Piece)
Couldn't load pickup availability
Please confirm the part number and compatibility before ordering.
Complete Your Order
Motul Chain Maintenance Kit – C1 Chain Cleaner + C2 Chain Lube Road (150ml Each) – Motorcycle O-Ring/X-Ring/Z-Ring Compatible
33081208 - Metal Polishing - 15Gms Royal Enfield Metal Polish Chrome Polish For Bullet
Adds: 15 GMS
Deutsche DEUS-1035Y Black Indicator with Amber Lens – Classic 350 BS6 UCE & Classic 500 UCE
Looking for a black indicator with an amber/orange lens for a Royal Enfield Classic 350 UCE BS6 or Classic 500 UCE, or replacing chrome indicators with a black look? The Deutsche DEUS-1035Y is an aftermarket turn-signal/blinker assembly with a black body and black mounting stalk, amber lens, threaded mounting stud and two-wire lead. The manufacturer's original catalogue identifies it as the front-left indicator for the Classic 500 Stealth Black (2017 type), cross-referenced to Royal Enfield 590602/A. The same black/amber design may be used on other matching UCE indicator positions and compatible Classic 350 UCE BS6 motorcycles after checking the actual mounting and wiring.
YOU ARE BUYING: ONE (1) BLACK-HOUSING, AMBER-LENS INDICATOR. This listing is not a pair or a set of four. Although the Swiss carton identifies DEUS-1035Y as “Front Left”, it can also be used at the front right, rear left or rear right on a compatible UCE installation provided the stalk fit, orientation, wire length and connector match. Manufacturer-assigned positions may use different factory part numbers, so the designation alone is not a guarantee of plug-and-play fit at every position.
Vehicle compatibility, all four positions and black-finish conversions
- Classic 350 UCE BS6 (pre-Reborn): Suitable as a replacement or black-finish styling alternative where the existing assembly uses compatible mounting and the matching two-wire/two-pin connection. This specifically means the UCE-engine Classic 350 BS6, not the later 349 cc J-series Classic Reborn.
- Classic 500 UCE / Stealth Black: Manufacturer-listed fit is 2017-type Stealth Black, front left, with Royal Enfield part reference 590602/A. The black/amber indicator may also be fitted to another position if the bike's hardware and wiring match.
- Position choice: front left (FLH), front right (FRH), rear left (RLH), or rear right (RRH) on a matching UCE setup. Check stalk position/angle, fitment clearance, thread, lead length and connector at the actual position.
- Chrome-to-black conversion: A practical option for riders of matching UCE Classic 350/500 motorcycles who prefer a black indicator housing rather than chrome. One piece is supplied; order the required quantity separately for two- or four-indicator conversions.
- Colour and wiring: Black housing and stalk + amber/orange lens, with a two-wire lead and white two-pin plug on this supplied configuration. Verify terminal/pin assignment against the original harness before connecting.
MODEL GENERATION WARNING: “Classic 350 BS6” covers two different generations: the older UCE BS6 and the Classic 350 Reborn/J-series. This DEUS-1035Y listing is for matching UCE-style indicator installations and does not establish compatibility with the J-series Reborn, new Bullet J-series, Meteor or Hunter. Do not assume compatibility with Thunderbird or every Standard/Electra variant merely because the indicators look similar.
Specifications and what's included
| Brand | Deutsche / Swiss Auto – aftermarket replacement, not genuine Royal Enfield |
|---|---|
| Part / SKU | DEUS-1035Y |
| Product | Motorcycle indicator / turn signal / blinker / trafficator assembly |
| Housing colour | Black (not chrome) |
| Lens colour | Amber / orange (not clear/smoked) |
| Manufacturer's position reference | Classic 500 Stealth Black 2017 type – front left (FLH), RE 590602/A |
| Other UCE installation positions | FLH / FRH / RLH / RRH where mounting orientation, threaded stem, cable routing, wiring and connector are physically compatible |
| Additional buyer application | Classic 350 BS6 UCE / pre-Reborn with matching indicator arrangement; also useful for chrome-to-black styling conversions |
| Connection | Two-wire lead, white two-pin connector; match original vehicle plug and pin functions |
| Mounting | Threaded stalk and securing nut; confirm bracket clearance, stem angle and wire length at selected position |
| Contents per retail order | One black/amber indicator assembly (not a pair) |
| Price note | ₹436 is the printed MRP on a factory carton marked 1U (2N), not a verified single-piece retail price |
Why the box says Front Left – and when it works at other positions
Swiss's catalogue names DEUS-1035Y “Front Left” for Classic 500 Stealth Black. That is the catalogue / factory-reference position, but the outer black/amber assembly can also be fitted at front right, rear left or rear right on a compatible UCE setup when the bracket angle, thread, lead reach and two-pin wiring allow. In a complete original-configuration parts restoration, the manufacturer lists separate position-specific codes. Use the table below to distinguish an exact catalogue match from a physically matched alternative.
| Vehicle location | Official Stealth Black 2017 catalogue reference | Can DEUS-1035Y be used? |
|---|---|---|
| Front left (FLH) | DEUS-1035Y / RE 590602/A | Yes – directly catalogue-listed on the specified Classic 500 Stealth Black |
| Front right (FRH) | DEUS-1035YA / RE 590601/A | Possible on matching UCE mount/wiring; not the manufacturer-assigned FRH part |
| Rear left (RLH) | DEUS-1035YB / RE 590604/A | Possible on matching UCE mount/wiring; not the manufacturer-assigned RLH part |
| Rear right (RRH) | DEUS-1035YC / RE 590603/A | Possible on matching UCE mount/wiring; not the manufacturer-assigned RRH part |
Buying tip: If you simply want the black/amber look on your Classic 350 UCE BS6 or another UCE Classic with compatible indicator mounts and connectors, the “FLH” label need not restrict you to that one position. However, this is not a manufacturer-certified universal four-position OEM interchange. If the existing stalk bends a different way, its cable is too short or the connector differs, select the position-specific part or verify installation with a qualified technician before ordering.
Deutsche aftermarket vs genuine Royal Enfield
This is a Deutsche-branded aftermarket indicator, not a genuine Royal Enfield-labelled part. For a factory-catalogue position-specific genuine replacement, see Royal Enfield Classic 500 UCE genuine indicator assemblies – 590601 / 590602 / 590603 / 590604 (select position). For broader Classic 350 and Classic 500 UCE OEM choices, see Royal Enfield UCE indicator assemblies (front/rear, LH/RH options). Those OEM parts may have chrome finish and separate connector specifications: choose based on your motorcycle and desired appearance.
How to identify the correct replacement
- Confirm your motorcycle is a UCE Classic 350 BS6/pre-Reborn or Classic 500 UCE with the matching indicator mounting arrangement.
- Choose the location to repair or customise: front left, front right, rear left or rear right. The official Stealth Black manufacturer designation is front left, but physical interchange may be possible at the other three positions.
- Compare housing colour (black), lens colour (amber), mounting stem thickness/thread, bracket orientation, indicator head angle, cable exit and lead length with the location you intend to use.
- Verify the white two-pin plug shape, pin layout and electrical functions. Wires that look similar may still be pinned differently; do not assume colour identifies polarity.
- For a chrome-to-black refresh, calculate whether you need one, two or four individual indicators; a single retail order of this SKU supplies one unit only.
Chrome-to-black conversion on a Classic 350 UCE BS6
The Classic 350 UCE BS6 (the pre-Reborn 346 cc UCE motorcycle) can use a black-housing, amber-lens replacement when its existing two-pin indicator wiring and mounting location are compatible. This is a visual replacement for riders who want to move away from chrome indicators, or repair a damaged black indicator. It does not convert a bulb indicator into an LED light and does not guarantee compatibility with every 2020–2021 trim or a previously modified wiring harness.
Not for Classic Reborn/J-series: Do not confuse UCE BS6 with the later 349 cc J-series Classic 350. The newer model's connector, bracket and indicator parts can be different. Also do not treat this as a universal direct-fit indicator for Hunter, Meteor, new Bullet or Thunderbird.
When would you replace it?
Replace a damaged indicator when its lens, housing, mounting stalk, connection or bulb holder is compromised. A turn signal that fails to flash may also have a wiring, connector, bulb, flasher relay, switch or ground problem; diagnose the circuit before ordering a complete assembly. The part is a turn signal, not a headlight, auxiliary light or brake lamp.
Installation and electrical precautions
- Switch off the ignition and isolate the battery as appropriate before repairing the indicator circuit.
- Remove the old indicator without pulling on the harness. Route the replacement lead away from hot and moving components.
- Match the connector orientation and mounting bracket, then tighten the threaded stem without overtightening or cracking the housing.
- Test left-side flashing, flashing rate, indicator illumination and clearance before riding. If the connector differs, do not force it or splice wires without identifying their functions.
- Do not infer the installed bulb wattage or type solely from the outer lens. If necessary, inspect the actual bulb specification before replacement.
Frequently asked questions
1. Is this the front-left indicator for the Classic 500 Stealth Black?
Yes. Swiss lists DEUS-1035Y for the 2017-type Classic 500 Stealth Black front-left position, cross-referenced with RE 590602/A. Other matching UCE locations can accept this physical design after the fitting checks described above.
2. Can I use this at the front-right position?
Yes, it can be used at front right on a UCE motorcycle where the stem, mounting angle, cable length and two-pin wiring are compatible. The catalogue-assigned front-right Stealth Black part is DEUS-1035YA; DEUS-1035Y is not automatically a plug-and-play OEM replacement for that number.
3. Can it be installed at rear left?
It can be fitted at rear left on a physically compatible UCE installation. Check the stalk orientation, mounting hardware, reach and connector. The factory-listed Stealth Black rear-left part is DEUS-1035YB.
4. Can it be fitted at rear right?
Yes, where the mounting and wiring physically match. The official Stealth Black rear-right reference is DEUS-1035YC, so verify carefully before using DEUS-1035Y as an alternative.
5. Does “Front Left” on the box mean it is ONLY for the front left?
No. Front Left is Swiss’s original catalogue position for the Classic 500 Stealth Black. The same black/amber style may be used in any of the four positions on a compatible UCE motorcycle; it is not a guarantee of factory-equivalent plugs, stalk angles or cable lengths across all four positions.
6. Does it fit the Classic 350 BS6 UCE?
It can be used for Classic 350 BS6 UCE/pre-Reborn motorcycles with matching indicator mounting and two-pin wiring. Compare the original before ordering. BS6 alone is not proof of compatibility because the later J-series Classic is also BS6.
7. Is it suitable for Classic 350 Reborn or the J-series?
No J-series fitment has been established. This listing is intended for matching UCE-era hardware, not Reborn, new Bullet J-series, Meteor or Hunter.
8. Can it be used on Thunderbird, Electra or Bullet Standard?
Not as a confirmed direct fit from this listing. Similar-looking indicator assemblies can use other stalks and connectors. Match the existing part before considering such a conversion.
9. Is this a genuine Royal Enfield indicator?
No. It is a Deutsche / Swiss Auto aftermarket part cross-referenced against RE 590602/A.
10. What colour are the housing and lens?
The body/stalk are BLACK, and the lens is AMBER/ORANGE. This is not a chrome-body indicator and not a clear-lens indicator.
11. Is the connector a two-pin type?
The displayed assembly has a white two-pin connector and two-wire lead. Confirm the mating connector shape and pin arrangement on your motorcycle before ordering.
12. Is this an LED indicator?
It is not described as an LED conversion kit. The manufacturer identifies a conventional blinker assembly for the specified Stealth Black configuration; the exact installed bulb should be checked on the physical part.
13. Do I receive two indicators because the manufacturer's carton mentions “2N”?
No. This retail listing is for one front-left indicator only. Manufacturer cartons may be packed in multiples; carton quantity does not change this product's one-piece retail contents.
14. Can I buy two or four to replace my chrome indicators?
Yes. Order the required number of individual pieces to create a pair or replace all four, after confirming the physical mounting and wiring at each location. This retail listing supplies ONE indicator per quantity ordered.
15. Does it include an indicator mounting bracket for the motorcycle?
The assembly has its own threaded mounting stalk and fastening nut. A separate motorcycle bracket, complete harness or flasher relay is not included unless specifically listed.
16. What if I have a replaced or modified wiring harness?
Verify the connector and wiring with the existing system. An altered harness can prevent a straightforward connection even if the exterior of the indicator looks the same.
17. Should I buy a new assembly if the turn signal flashes too fast?
Not automatically. Incorrect bulb load, relay selection, poor contacts or wiring faults can also cause abnormal flash rates. Diagnose the circuit first.
18. What do the other Swiss part numbers refer to?
The manufacturer catalogue identifies Stealth Black front left DEUS-1035Y / 590602/A, front right DEUS-1035YA / 590601/A, rear left DEUS-1035YB / 590604/A, and rear right DEUS-1035YC / 590603/A. Those are official position references; this black/amber unit can be a physically matched alternative where the existing UCE installation allows.
19. Can I replace a chrome indicator with this black one?
Yes, for a compatible Classic 350 UCE BS6/pre-Reborn or Classic 500 UCE indicator installation. You receive a black housing with an amber lens; verify the mount, wiring and two-pin connector first. A full set requires purchasing multiple pieces.
20. Does BS6 mean Classic 350 Reborn?
No. The earlier 346 cc UCE Classic 350 was sold in a BS6 version before the newer 349 cc J-series Classic Reborn. This UCE-oriented aftermarket indicator should not be bought for a J-series model merely because both motorcycles meet BS6 emission standards.
21. Is it an OEM-certified replacement for all four sides?
No. The manufacturer officially lists DEUS-1035Y for front left on the 2017-type Stealth Black. Use at front right, rear left or rear right is a mounting-and-wiring-dependent alternative for compatible UCE installations, not a manufacturer-certified four-way interchange.
What is supplied — please read
One (1) Deutsche DEUS-1035Y indicator, BLACK BODY with AMBER LENS. Suitable for matching UCE Classic setups, including compatible Classic 350 UCE BS6 and Classic 500 UCE bikes. Although labelled front left for Stealth Black, it may be installed at other matching front/rear positions after checking the mounting and wiring. No pair / no set of four; no additional motorcycle-specific bracket, harness or relay. Packaging may vary.
Order carefully: Confirm UCE rather than Reborn/J-series; confirm BLACK + AMBER appearance and the actual connector/stalk fit at your chosen location. Other UCE positions are conditional fits, not necessarily OE-catalogue interchangeability. Inspect electrical parts before fitting and follow the store's published electrical-component and unboxing-video policies.
Share
Verify Fitment on Official Brand Portals
Verify Fitment on Official Brand Portals
For selected genuine spare parts, you can cross-check the part number on the official brand portals before ordering.
Royal Enfield Official Spares Portal
Hero MotoCorp Official eCatalogue

Become a Dealer Partner
We supply 100% genuine OEM parts to workshops and dealers across India. Our team will reach out within 24 hours.